Application of seeding machine


Now,planterIt has been widely used and is a good seeder. Planters for certain types or crops are often named after the type of crop, such as wheat planters and cotton planters. The soil should be cleaned from all parts of the pot. Remove seeds and fertilizer from the fertilizer tank. Especially the fertilizer tank, after washing and drying with water, the fertilizer tank (except plastic tank) should be coated with anti-corrosion paint. Check the planter for damaged or worn parts, replace or repair if necessary, and repaint the parts with peeling paint.

 

播种机

 

After using the new planter, if you choose a disc opener, you should remove it, clean the outer cone, disc hub and linoleum with diesel or gasoline, and then install it with butter. If there is deformation, it should be leveled. If the focus gap of the disc is too large, it can be adjusted by reducing the adjustment shim between the inner cone and the outer cone. After cleaning the soil working parts, apply butter or waste oil to avoid rust. The planter should be stored in a dry and ventilated warehouse or shed to avoid outdoor storage. When storing, the shelf should be firmly supported, and the bottle opener and lid should be filled with wooden boards and should not directly touch the ground. The rubber or plastic seed and fertilizer pipes on the planter should be removed, wiped clean, tied up and stored on the box or shelf. Sand or hay can be filled into the pipe to avoid squeezing, folding and deformation. After the planter is stored for a long time, it should be maintained and repaired in advance before sowing in the next season to keep the equipment in good technical condition.
Planter maintenance:
Before operation, the planter should inject oil to each injection point in time to ensure that the running parts are fully lubricated. Lost or damaged parts should be repaired, replaced and repaired in time. Be careful not to oil the gears and chains to avoid sticky dirt and increased wear. The disc of the disc ditching machine shall roll flexibly and shall not shake or rub the body of the ditching machine. At the end of each shift, the fertilizer in the fertilizer box should be cleaned to avoid corrosion of the fertilizer box and fertilizer discharge components. Check whether the rolling of the seed row and fertilizer row axis is flexible. After each shift, the planter should be parked in a dry covered shed. When parking in the open air, cover the fertilizer box tightly. When parking, drop the trencher, put down the bracket, stably support the body, and reduce unnecessary load on the planter frame.
A planter that spreads the sown seeds evenly on the sowing ground. The commonly used model is the centrifugal seeder, attached to the rear of the agricultural transport vehicle. It consists of a seed box and a sowing wheel. From the seed box to the sowing wheel, the seeds are sown in the tangential direction under the action of centrifugal force, and the sowing amplitude is 8-12m. Powder or granular fertilizer, lime and other materials can also be sown. The broadcasting device can also be installed on agricultural aircraft.
Want to know moreRake, Subsoiler, Disc PloughThe content, can pay attention to us.



Related News


Drive disc harrow price, deep loosening machine price: correct use and maintenance of disc harrow, deep loosening machine

The correct use and maintenance of the disc harrow: in operation, the technical condition of the rake, scraper, square shaft, bearing, angle adjuster and connecting parts should be checked frequently, especially the end nut of the disc harrow group and the fixing bolts of each bearing. If it is found loose, tighten it in time, and remove the weeds and dirt on the workpiece in time.


How to maintain planter accessories

Planter A planting machine using crop seeds as a planting object. Planters for a certain type or crop are usually named after the crop type, such as wheat planter, cotton planter, etc. Planter accessories are very effective in farmland operations, so the planter accessories are easily damaged. Next, the planter manufacturer will introduce how to maintain the planter accessories. Before using the planter, we should have a simple and comprehensive understanding of the principles of all planter accessories. The planter manufacturer stated that it can be effective as long as the maintenance is carried out on the correct accessories to ensure the normal use of the planter accessories. The planter will extend its life.


Defects in castings and forgings

The defects produced in the casting and forging process are similar to the defects produced in the ingot, but they are still process defects, including pores, inclusions, shrinkage holes, loose holes, cracks, etc.


Production of castings and forgings

Castings and forgings must be melted by electric furnaces, mainly electric arc furnaces and induction furnaces. According to the different lining materials and slag system, can be divided into acidic furnace and alkaline furnace. Carbon steel and low alloy steel can be smelted in any furnace, but high alloy steel can only be smelted in alkaline furnaces.


Inspection of Casting and Forging

The complex information system management interface of casting and forging, such as poor ultrasonic penetration, coarse grain, uneven organization, etc., all enhance the scattering of an ultrasonic wave by students, and the energy can be effectively attenuated, so that the detectable thickness is smaller than that of forgings.


What are the advantages and disadvantages of casting and forging

One of the advantages of casting and forging is the flexibility of design. Personnel design has a large degree of freedom of design choice for the shape and size of castings, especially for parts with complex shapes and hollow sections. Steel castings can be manufactured using a unique process known as core assembly.