Arrangement of disc harrow


disc harrowIt is composed of rake frame, rake group, traction or suspension device and deflection adjustment mechanism. In order to increase the depth of the soil, some light and small rakes are equipped with counterweight boxes on the rake frame. The disc harrows produced and used in the 1980 s distributed a relatively large weight on each disc and had sufficient soil penetration capacity, so there was no need to add weights and adjust the deflection angle. When installing the rake group, the deflection angle of the disc rake group should be fixed at the best position. When shallow tillage is required, wheels controlled by hydraulic cylinders limit the depth.

 

 

圆盘耙


 

 

The towed rake is usually equipped with a device that can automatically adjust the transport state and manually fine-tune the working state on the towing device. With the lifting of wheels and connecting rods, the rake is always level
Commonly used disc harrows have the following configurations:
disc harrowThe left and right sides of a single row of opposite rake groups are arranged in a row, and the left and right rows are respectively composed of one or more concave opposite rake groups. It is used for flats of irrigated land, stubble after harvest and shallow cultivation of fallow land.
Front and rear two rows: each row of disc harrows is symmetrically arranged by two rows of left and right harrows. The concave surfaces of the discs of the first two rows of tine groups are opposite each other. The discs of the rear two rows of rake sets are located between the two discs of the front rake set and opposite the concave surface. In order to avoid the left rake group and right rake group of the opposite rake of the disc rake leaving missing areas at the junction of the left and right rakes, some opposite rakes make the left and right rakes staggered.


 

 

圆盘耙

 

 

The offset type consists of two rows of forward tilt groups, each with an opposing disc concave surface. Since the lateral force of the front and rear rake groups is balanced with the traction, the width centerline of the disc rake may deviate from the longitudinal axis of the tractor during operation, so it is called an offset rake. The bias of the wide bias rake can reach more than 3 meters. When used in orchards, the offset rake can be expanded to the point where it is inaccessible.disc harrowThe tractor works under the hood. Since the offset rake has no missing farming area, it is also widely used in field operations.deep loosening machine,disc ploughIt is also increasingly present in the agricultural sector.

Related News


Drive disc harrow price, deep loosening machine price: correct use and maintenance of disc harrow, deep loosening machine

The correct use and maintenance of the disc harrow: in operation, the technical condition of the rake, scraper, square shaft, bearing, angle adjuster and connecting parts should be checked frequently, especially the end nut of the disc harrow group and the fixing bolts of each bearing. If it is found loose, tighten it in time, and remove the weeds and dirt on the workpiece in time.


How to maintain planter accessories

Planter A planting machine using crop seeds as a planting object. Planters for a certain type or crop are usually named after the crop type, such as wheat planter, cotton planter, etc. Planter accessories are very effective in farmland operations, so the planter accessories are easily damaged. Next, the planter manufacturer will introduce how to maintain the planter accessories. Before using the planter, we should have a simple and comprehensive understanding of the principles of all planter accessories. The planter manufacturer stated that it can be effective as long as the maintenance is carried out on the correct accessories to ensure the normal use of the planter accessories. The planter will extend its life.


Defects in castings and forgings

The defects produced in the casting and forging process are similar to the defects produced in the ingot, but they are still process defects, including pores, inclusions, shrinkage holes, loose holes, cracks, etc.


Production of castings and forgings

Castings and forgings must be melted by electric furnaces, mainly electric arc furnaces and induction furnaces. According to the different lining materials and slag system, can be divided into acidic furnace and alkaline furnace. Carbon steel and low alloy steel can be smelted in any furnace, but high alloy steel can only be smelted in alkaline furnaces.


Inspection of Casting and Forging

The complex information system management interface of casting and forging, such as poor ultrasonic penetration, coarse grain, uneven organization, etc., all enhance the scattering of an ultrasonic wave by students, and the energy can be effectively attenuated, so that the detectable thickness is smaller than that of forgings.


What are the advantages and disadvantages of casting and forging

One of the advantages of casting and forging is the flexibility of design. Personnel design has a large degree of freedom of design choice for the shape and size of castings, especially for parts with complex shapes and hollow sections. Steel castings can be manufactured using a unique process known as core assembly.