What are the operating precautions of the deep loosening machine?


1. It is forbidden for staff to work in a state of fatigue or after drinking and at night.deep loosening machineThe staff cannot lend it to personnel who do not know the safe operation method for operation.
2. The staff of the deep loosening machine must be familiar with the operation instructions and operate in strict accordance with the safe operation method.
3. In the use of the staff must pay attention to the safety signs on the machine, and also carefully read the contents of the signs.
4. Every Usedeep loosening machineAll the staff should wear clothes that conform to the labor protection function according to the requirements, so as to prevent the winding of moving parts from causing safety accidents.
5. Before each use operation, be sure to check whether the lubricating oil of the engine and transmission box of the subsoiling machine is sufficient. Whether the bolts of each part are loose and fall off.deep loosening machineWhether the engine, transmission box, clutch, brake system and other operating parts can still be used normally. Is its gear lever in the neutral position. Whether the exposed rotating parts are properly shielded.
6. The deep loosening machine must be symmetrical left and right when installing the tool, and the working blade should be forward. It is recommended to install bolts, bolts, etc. to fix the tool to ensuredeep loosening machineCan be safe production operations.
7. The height of the resistance rod can be adjusted at any time according to the actual situation of the work, so as to ensure the stable position of the fuselage and prevent excessive tilt of the engine, resulting in poor lubrication and damage to the transmitter.
8.deep loosening machineAfter the engine is started, the applied no-load operation is five to ten minutes. It is recommended not to run at high speed and work with heavy load within one to two hours before the operation. This can also extend the use time. If the engine is running when starting, be sure to immediately cut off the fuel supply and stop the engine.
9.deep loosening machineIn the field ditch, canal and other operations to low-speed gear operation. When working in Dapeng, ensure good ventilation to allow air convection and exhaust gas.

Related News


Drive disc harrow price, deep loosening machine price: correct use and maintenance of disc harrow, deep loosening machine

The correct use and maintenance of the disc harrow: in operation, the technical condition of the rake, scraper, square shaft, bearing, angle adjuster and connecting parts should be checked frequently, especially the end nut of the disc harrow group and the fixing bolts of each bearing. If it is found loose, tighten it in time, and remove the weeds and dirt on the workpiece in time.


How to maintain planter accessories

Planter A planting machine using crop seeds as a planting object. Planters for a certain type or crop are usually named after the crop type, such as wheat planter, cotton planter, etc. Planter accessories are very effective in farmland operations, so the planter accessories are easily damaged. Next, the planter manufacturer will introduce how to maintain the planter accessories. Before using the planter, we should have a simple and comprehensive understanding of the principles of all planter accessories. The planter manufacturer stated that it can be effective as long as the maintenance is carried out on the correct accessories to ensure the normal use of the planter accessories. The planter will extend its life.


Defects in castings and forgings

The defects produced in the casting and forging process are similar to the defects produced in the ingot, but they are still process defects, including pores, inclusions, shrinkage holes, loose holes, cracks, etc.


Production of castings and forgings

Castings and forgings must be melted by electric furnaces, mainly electric arc furnaces and induction furnaces. According to the different lining materials and slag system, can be divided into acidic furnace and alkaline furnace. Carbon steel and low alloy steel can be smelted in any furnace, but high alloy steel can only be smelted in alkaline furnaces.


Inspection of Casting and Forging

The complex information system management interface of casting and forging, such as poor ultrasonic penetration, coarse grain, uneven organization, etc., all enhance the scattering of an ultrasonic wave by students, and the energy can be effectively attenuated, so that the detectable thickness is smaller than that of forgings.


What are the advantages and disadvantages of casting and forging

One of the advantages of casting and forging is the flexibility of design. Personnel design has a large degree of freedom of design choice for the shape and size of castings, especially for parts with complex shapes and hollow sections. Steel castings can be manufactured using a unique process known as core assembly.