Maintenance of planter


planterNow widely used, better than the planter machine. Planters are used for a certain type or crop usually named after the type of crop, such as wheat planter, cotton planter. Below we will introduce how to scientifically maintain the planter and so on. The planter should clean all parts of the soil. Remove seeds and fertilizer from the fertilizer tank. Especially the fertilizer tank, after rinsing with clean water and drying, apply anti-corrosion paint on the fertilizer tank (except plastic tank). Check the planter for damaged and worn parts, replace or repair if necessary, and repaint the parts with peeling paint.
Use a new planter. If you choose an opener, you should remove it, clean the outer cone, disc hub and linoleum with diesel or gasoline, and then install it with butter. If there is deformation, it must be flattened. If the focus gap of the disc is too large, it can be adjusted by reducing the adjustment shim between the inner cone and the outer cone. After cleaning dirty working parts, apply butter or waste oil to avoid rust.
The planter should be stored in a dry and ventilated warehouse or shed, and avoid open storage. When storing, the shelf should be firmly supported, and the bottle opener and lid should be filled with wooden boards, and do not directly touch the floor. The rubber or plastic seed delivery pipes and fertilizer pipes on the planter should be removed, wiped clean, tied up and stored in boxes or shelves. Sand or hay can be filled into the pipe to avoid squeezing, folding and deformation. After the planter is stored for a long time, it should be maintained and repaired in advance before sowing in the next season to keep the equipment in good technical condition.
Planter maintenance:
Before the operation of the seeder, oil should be injected into each oil injection point in time to ensure that the running parts are fully lubricated. The lost or damaged parts shall be filled, replaced and repaired in time. Be careful not to apply oil on the gears and chains to avoid slime and increased wear. The disc of the disc ditching machine is flexible in rolling, does not shake, and does not rub against the body of the ditching machine. After each shift, the fertilizer in the fertilizer box should be cleaned to avoid corrosion of the fertilizer box and the position of fertilizer discharge. Check whether the sowing shaft and the fertilizing shaft rotate flexibly. After each shift, the planter should be parked in a dry and covered carport. When parking in open air, the cover of fertilizer box should be sealed tightly. When parking, the trencher should be put down, the bracket should be put down to stabilize the fuselage, and reduce unnecessary load on the planter frame.
Folding drill
Mainly used for cereals, vegetables, grass and other small seed cultivation., And commonly used is the grain drill. When working, the walking wheel drives the seed wheel to rotate, and the seeds from the seed box are discharged into the seed pipe according to the required cultivation amount, and then fall into the opened groove through the opener, and then the seeds are covered and compacted by the soil covering compaction equipment. After emergence, the crops are arranged in parallel equidistant rows. In addition to different types of seeder and opener, the drilling rig structure of different crops is basically the same, generally by the frame, traction or suspension equipment, seed box, seeder, transmission equipment, seed pipe, opener, dicing machine, walking wheel, soil pressure equipment and other components. At the same time, sowing equipment and furrow opener are the main factors affecting the quality of cultivation. Commonly used seeding devices are slot wheel, centrifugal and grinding wheel. Trenchers have hoe shovel type, shoe type, sliding knife type, single disc type and double disc type.

Related News


Drive disc harrow price, deep loosening machine price: correct use and maintenance of disc harrow, deep loosening machine

The correct use and maintenance of the disc harrow: in operation, the technical condition of the rake, scraper, square shaft, bearing, angle adjuster and connecting parts should be checked frequently, especially the end nut of the disc harrow group and the fixing bolts of each bearing. If it is found loose, tighten it in time, and remove the weeds and dirt on the workpiece in time.


How to maintain planter accessories

Planter A planting machine using crop seeds as a planting object. Planters for a certain type or crop are usually named after the crop type, such as wheat planter, cotton planter, etc. Planter accessories are very effective in farmland operations, so the planter accessories are easily damaged. Next, the planter manufacturer will introduce how to maintain the planter accessories. Before using the planter, we should have a simple and comprehensive understanding of the principles of all planter accessories. The planter manufacturer stated that it can be effective as long as the maintenance is carried out on the correct accessories to ensure the normal use of the planter accessories. The planter will extend its life.


Defects in castings and forgings

The defects produced in the casting and forging process are similar to the defects produced in the ingot, but they are still process defects, including pores, inclusions, shrinkage holes, loose holes, cracks, etc.


Production of castings and forgings

Castings and forgings must be melted by electric furnaces, mainly electric arc furnaces and induction furnaces. According to the different lining materials and slag system, can be divided into acidic furnace and alkaline furnace. Carbon steel and low alloy steel can be smelted in any furnace, but high alloy steel can only be smelted in alkaline furnaces.


Inspection of Casting and Forging

The complex information system management interface of casting and forging, such as poor ultrasonic penetration, coarse grain, uneven organization, etc., all enhance the scattering of an ultrasonic wave by students, and the energy can be effectively attenuated, so that the detectable thickness is smaller than that of forgings.


What are the advantages and disadvantages of casting and forging

One of the advantages of casting and forging is the flexibility of design. Personnel design has a large degree of freedom of design choice for the shape and size of castings, especially for parts with complex shapes and hollow sections. Steel castings can be manufactured using a unique process known as core assembly.