Do you use the storage method of the deep loosening machine for a long time?


In the purchasedeep loosening machineIt can be subsidized by the relevant departments, because it can improve the structure of the soil. It is also very convenient and flexible when used, easy to use, and the price is relatively low. At present, it has also been widely used in agriculture. However, there are still many users who do not know much about the correct use of the subsoiling machine, such as the maintenance and repair of the subsoiling machine and the precautions related to storage and maintenance, which will affect the use time and performance of the subsoiling machine. If we are sure not to use it for a long time, we must follow the following method to put it into storage. The following is a brief introduction to the storage method of subsoiling machine that is not used for a long time!

1.deep loosening machineThe engine should run on its own at low speed for about five minutes to stop.

2. When the engine of the subsoilers is still relatively hot, drain the lubricating oil and replace it with new oil.

3. We have to take out the rubber plug on the cylinder head, and then givedeep loosening machineAdd a little bit of oil, reduce the operating lever to a position where there is no compression, and then pull the recoil-type starting handle two to three times.

4. The decompression handle of the deep loosening machine should be placed in the compressed position, then slowly pull out the recoil start handle, and then put it in the compressed position to stop, so that the intake exhaust valve is closed and moisture will not enter the engine. The inside can prevent rust.

5. Then also in order to better preventdeep loosening machineExternal dirt and other stolen goods are contaminated, the machine should also be kept in a dry place.

6. Each operation machine should be rust-proof. It is suggested to keep it in the same place as the host to prevent loss.

The above is about thisdeep loosening machineSome introductions that have not been used for a long time, I hope you can help you after reading them.


Related News


Drive disc harrow price, deep loosening machine price: correct use and maintenance of disc harrow, deep loosening machine

The correct use and maintenance of the disc harrow: in operation, the technical condition of the rake, scraper, square shaft, bearing, angle adjuster and connecting parts should be checked frequently, especially the end nut of the disc harrow group and the fixing bolts of each bearing. If it is found loose, tighten it in time, and remove the weeds and dirt on the workpiece in time.


How to maintain planter accessories

Planter A planting machine using crop seeds as a planting object. Planters for a certain type or crop are usually named after the crop type, such as wheat planter, cotton planter, etc. Planter accessories are very effective in farmland operations, so the planter accessories are easily damaged. Next, the planter manufacturer will introduce how to maintain the planter accessories. Before using the planter, we should have a simple and comprehensive understanding of the principles of all planter accessories. The planter manufacturer stated that it can be effective as long as the maintenance is carried out on the correct accessories to ensure the normal use of the planter accessories. The planter will extend its life.


Defects in castings and forgings

The defects produced in the casting and forging process are similar to the defects produced in the ingot, but they are still process defects, including pores, inclusions, shrinkage holes, loose holes, cracks, etc.


Production of castings and forgings

Castings and forgings must be melted by electric furnaces, mainly electric arc furnaces and induction furnaces. According to the different lining materials and slag system, can be divided into acidic furnace and alkaline furnace. Carbon steel and low alloy steel can be smelted in any furnace, but high alloy steel can only be smelted in alkaline furnaces.


Inspection of Casting and Forging

The complex information system management interface of casting and forging, such as poor ultrasonic penetration, coarse grain, uneven organization, etc., all enhance the scattering of an ultrasonic wave by students, and the energy can be effectively attenuated, so that the detectable thickness is smaller than that of forgings.


What are the advantages and disadvantages of casting and forging

One of the advantages of casting and forging is the flexibility of design. Personnel design has a large degree of freedom of design choice for the shape and size of castings, especially for parts with complex shapes and hollow sections. Steel castings can be manufactured using a unique process known as core assembly.